问题的故障是主机断电后，solaris11起不来了。在boot阶段报错：ERROR: boot-read fail
以下是启动报错信息：
SPARC T4-1, No Keyboard Copyright (c) 1998, 2012, Oracle and/or its affiliates. All rights reserved. OpenBoot 4.34.1, 32256 MB memory available, Serial #101718426. Ethernet address 0:10:e0:10:19:9a, Host ID: 8610199a.
ERROR: boot-read fail Boot device: net File and args: 1000 Mbps full duplex Link up Requesting Internet Address for 0:10:e0:10:19:9a Requesting Internet Address for 0:10:e0:10:19:9a Requesting Internet Address for 0:10:e0:10:19:9a
由于在OBP中boot-device设置的是disk net, 从磁盘引导失败后，就自动从net引导了。此系统根本没配置net引导，因此一直在试着从网络上获取IP地址信息。
解决过程
1. 在ILOM里设置OS不自动启动
原系统在OBP里设置了auto-boot?=true，此处先在ILOM把自动启动去掉.
串口登录ILOM，设置OS不自动启动
set /HOST/bootmode script="setenv auto-boot? false"
重启
stop /SYS
start /SYS
切换到console
start /SP/console
启动后系统停止在ok状态
2. 检查一下磁盘情况
{0} ok probe-scsi-all /pci@400/pci@2/pci@0/pci@f/pci@0/usb@0,2/hub@2/hub@3/storage@2 Unit 0 Removable Read Only device AMI Virtual CDROM 1.00
/pci@400/pci@2/pci@0/pci@c/SUNW,qlc@0,1 QLogic QLE2562 Host Adapter FCode(SPARC): 2.03 06/30/08 Wait for link up - / Firmware version 4.03.02 Adapter portID - 10200 ************** Fabric Attached Devices ************** Dev# 0 (0) PortID 10000 Port WWN 200a00a0b848305a LUN 0(0) DISK SUN CSM200_R 0760 LUN 1(1) DISK SUN CSM200_R 0760 LUN 2(2) DISK SUN CSM200_R 0760 LUN 3(3) DISK SUN CSM200_R 0760 LUN 4(4) DISK SUN CSM200_R 0760
Dev# 1 (1) PortID 10100 Port WWN 200b00a0b848305a LUN 0(0) DISK SUN CSM200_R 0760 LUN 1(1) DISK SUN CSM200_R 0760 LUN 2(2) DISK SUN CSM200_R 0760 LUN 3(3) DISK SUN CSM200_R 0760 LUN 4(4) DISK SUN CSM200_R 0760
/pci@400/pci@2/pci@0/pci@c/SUNW,qlc@0 QLogic QLE2562 Host Adapter FCode(SPARC): 2.03 06/30/08 Wait for link up - / Firmware version 4.03.02 Adapter portID - 10200 ************** Fabric Attached Devices ************** Dev# 0 (0) PortID 10000 Port WWN 200a00a0b8483059 LUN 0(0) DISK SUN CSM200_R 0760 LUN 1(1) DISK SUN CSM200_R 0760 LUN 2(2) DISK SUN CSM200_R 0760 LUN 3(3) DISK SUN CSM200_R 0760 LUN 4(4) DISK SUN CSM200_R 0760 Dev# 1 (1) PortID 10100 Port WWN 200b00a0b8483059 LUN 0(0) DISK SUN CSM200_R 0760 LUN 1(1) DISK SUN CSM200_R 0760 LUN 2(2) DISK SUN CSM200_R 0760 LUN 3(3) DISK SUN CSM200_R 0760 LUN 4(4) DISK SUN CSM200_R 0760 /pci@400/pci@2/pci@0/pci@4/scsi@0
FCode Version 1.00.61 , MPT Version 2.00, Firmware Version 9.00.00.00
Target 9 Unit 0 Removable Read Only device TEAC DV-W28SS-V 1.0B SATA device PhyNum 6
/pci@400/pci@1/pci@0/pci@4/scsi@0
FCode Version 1.00.61 , MPT Version 2.00, Firmware Version 9.00.00.00
Target 381 Volume 0 Unit 0 Disk LSI Logical Volume 3000 583983104 Blocks, 298 GB VolumeDeviceName 3e90f849ae6f04a5 VolumeWWID 0e90f849ae6f04a5
/pci@400/pci@1/pci@0/pci@0/SUNW,qlc@0,1 QLogic QLE2562 Host Adapter FCode(SPARC): 2.03 06/30/08 Wait for link up - / Firmware version 4.03.02 Adapter portID - 10300 ************** Fabric Attached Devices ************** Dev# 0 (0) PortID 10000 Port WWN 200a00a0b848305a LUN 0(0) DISK SUN CSM200_R 0760 LUN 1(1) DISK SUN CSM200_R 0760 LUN 2(2) DISK SUN CSM200_R 0760 LUN 3(3) DISK SUN CSM200_R 0760 LUN 4(4) DISK SUN CSM200_R 0760 Dev# 1 (1) PortID 10100 Port WWN 200b00a0b848305a LUN 0(0) DISK SUN CSM200_R 0760 LUN 1(1) DISK SUN CSM200_R 0760 LUN 2(2) DISK SUN CSM200_R 0760 LUN 3(3) DISK SUN CSM200_R 0760 LUN 4(4) DISK SUN CSM200_R 0760 /pci@400/pci@1/pci@0/pci@0/SUNW,qlc@0 QLogic QLE2562 Host Adapter FCode(SPARC): 2.03 06/30/08 Wait for link up - / Firmware version 4.03.02 Adapter portID - 10300 ************** Fabric Attached Devices ************** Dev# 0 (0) PortID 10000 Port WWN 200a00a0b8483059 LUN 0(0) DISK SUN CSM200_R 0760 LUN 1(1) DISK SUN CSM200_R 0760 LUN 2(2) DISK SUN CSM200_R 0760 LUN 3(3) DISK SUN CSM200_R 0760 LUN 4(4) DISK SUN CSM200_R 0760 Dev# 1 (1) PortID 10100 Port WWN 200b00a0b8483059 LUN 0(0) DISK SUN CSM200_R 0760 LUN 1(1) DISK SUN CSM200_R 0760 LUN 2(2) DISK SUN CSM200_R 0760 LUN 3(3) DISK SUN CSM200_R 0760 LUN 4(4) DISK SUN CSM200_R 0760
上述输出中显示为LUN的，都是来自存储的空间。红色部分是本地盘。此系统设置了硬RAID.
3. 检查硬RAID信息
{0} ok select /pci@400/pci@1/pci@0/pci@4/scsi@0 {0} ok show-volumes Volume 0 Target 381 Type RAID1 (Mirroring) Name ids1vol WWID 0e90f849ae6f04a5 Optimal Enabled Volume Not Consistent 2 Members 583983104 Blocks, 298 GB Disk 1 Primary Optimal Target 9 HITACHI H106030SDSUN300G A2B0 PhyNum 0 Disk 0 Secondary Optimal Target a HITACHI H106030SDSUN300G A2B0 PhyNum 1
{0} ok unselect-dev
4. 从指定路径启动OS
从自动启动报错的信息来看(ERROR: boot-read fail) ，很可能是启动时没找到引导块。这并不一定表示磁盘坏了或者引导块坏了，也有可能是找的位置不对。一般情况下，主机掉电并不会造成磁盘出现损坏这么严重的问题。于是手工指定路径来启动OS.
{0} ok boot /pci@400/pci@2/pci@0/pci@4/scsi@0/disk@w3e90f849ae6f04a5,0:a Boot device: /pci@400/pci@1/pci@0/pci@4/scsi@0/disk@w3e90f849ae6f04a5,0:a File and args: SunOS Release 5.11 Version 11.0 64-bit Copyright (c) 1983, 2011, Oracle and/or its affiliates. All rights reserved. .....
结果系统起来了。
至于为什么是这个启动路径，我也不太清楚，完全是矇的。对于/pci@400/pci@1/pci@0/pci@4/scsi@0/disk@w3e90f849ae6f04a5,0:a 这个路径，大概情况如下：
/pci@400/pci@1/pci@0/pci@4/scsi@0 这个好理解，表示磁盘的系统PCI中的位置
/disk@ 这个是固定的
w3e90f849ae6f04a5 关键是这个值，此值相当于磁盘逻辑名称cXtYdZ中的"Y"，此值可能与以下内容有关。
Volume 0 Target 381 Type RAID1 (Mirroring) Name ids1vol WWID 0e90f849ae6f04a5
其中w是固定的，3估计是 "Target 381” 中的"3”, e90f849ae6f04a5是 WWID的值去掉前面的"0". 至于为什么是这样，我也不知道。只时当时我上网查的时候，刚好看到有个人的系统盘也是做了硬RAID，OS中的系统盘名称与此类似。我仔细分析了他的系统盘名称，做出了以上猜测。
,0:a 这个也好理解，0表示d0，即磁盘0；a表示分区0
5. 设置启动盘别名
系统起来后，需要设置一下别名，避免下次重启还得手工指定路径。
root@racnode1:~# eeprom "nvramrc=devalias bootdisk /pci@400/pci@1/pci@0/pci@4/scsi@0/disk@w3e90f849ae6f04a5,0:a" root@racnode1:~# eeprom boot-device="bootdisk" root@racnode1:~# eeprom "use-nvramrc?=true"
备注：w3e90f849ae6f04a5这个值实际上是probe-scsi-all命令输出的VolumeDeviceName值前面加上"w"
Target 381 Volume 0 Unit 0 Disk LSI Logical Volume 3000 583983104 Blocks, 298 GB VolumeDeviceName 3e90f849ae6f04a5 VolumeWWID 0e90f849ae6f04a5